Home>Bearing knowledge>Excavator timing protection matters

/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Excavator timing protection matters

---

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

At present, the hydraulic system of the excavator is equipped with intelligent equipment; the equipment has a warning function for certain dangers of the hydraulic system of the excavator; however, the scale and degree of monitoring have certain limitations; therefore, the inspection and protection of the hydraulic system of the excavator should be intelligent equipment. The monitoring results are combined with the timed view protection.
1250h view protection to view the attachments on the filter screen; if there is too much metal powder; it often marks the wear of the oil pump or the cylinder of the cylinder; for this; it is necessary to confirm the diagnosis and adopt the corresponding measures before starting the machine. If the filter is found, the dirt is damaged. Accumulate; replace in time; change oil if necessary.
2500h view protection should be replaced regardless of the condition of the excavator filter; it is difficult to detect the slight damage of the filter element due to the naked eye; if it is a long time high temperature operation, it should be replaced as early as possible.
31000h view protection to clear the excavator filter; replace the excavator filter; remove the excavator hydraulic tank; replace the excavator hydraulic oil. Long-term high-temperature operation oil change time should be appropriate early. Of course; if you can pass the oil quality analysis to guide the change Oil is the most economical; however, it is important to focus on the extended application of the oil; it should be tested every 100 hours; in order to find and replace the eucalyptus oil in time.
47000h and 10000h to check the hydraulic system of the protection excavator must be tested by professionals; make necessary adjustments and repairs. According to the theory; it is necessary to overhaul the hydraulic pump of the excavator and the hydraulic motor of the excavator after 10000h; otherwise the hydraulic pump and excavator of the excavator The motor can be damaged due to disrepair; it is a fatal damage to the hydraulic system of the excavator.

---

Recommend to friends comments close window

Bearing related knowledge

Introduction of the world-famous brand bearing The selection and application of the oscillating machine bearing skill analysis: the device of the automobile water pump shaft bearing INA flange bearing temperature rise "critical analysis" Characteristic classification of magnetic NSK bearing

This article links to http://
Please indicate China Bearing Network http://

Previous:Pressure ball bearing Next: Operation, protection and maintenance procedures for φ2100Χ3000 overflow ball mill

XB400 CAF Jointing Sheet

Description:XB400 CAF Jointing Sheet is made by good asbestos fiber with rubber ,compression molding it in thick paper fashion.

Usage:XB400 CAF Jointing Sheet is suitable for high temperature max 400℃ and high pressure max 5.0MPa,for water and saturated vapour,super vapour,gas inert gases transmitted in the joints of facilities and pipelines.

TEMP:400℃(max)

PRESS:5.0MPa(max)

Dimension:
4100×1500mm; 4500 x 1500mm;2000×1500mm;

1500×1500mm;1500×1000mm;1540x1360mm

1270×1300mm; 3810×1300mm 

Thickness:  0.5~6.0mm

Technical data:

Lateral Tensile Strength/MPa        â‰¥      15.0

Aging coefficient                   â‰¥       0.9

Loss on ignition/%                  â‰¤      28.0

Compression ratio/%                       7~17

Recovery/%                       â‰¥       45

Creep relaxation rate/%             â‰¤       50

Density(g/cm3)                           1.6~2.0

 

 Product photoes:

Xb400 Caf Jointing Sheet

Xb400 Caf Jointing Sheet,Jointing Sheet,steam jointing sheet,Gasket Joint Sheet

HEBEI HENGDA SEALING MATERIALS CO.,LTD. , https://www.hengdasealing.com